Top 10 typical forklift crashes ， forklift procedure need to pay attention to these issues ！.

Don't underestimate the forklift at the office. If the procedure is bad, there will certainly be serious accidents in minutes, and there are numerous mishaps including forklifts.

Situation 1: The forklift cargo blocked the motorist's sight, and the person in front might not be discovered, leading to a rolling accident.
Case 2: In order to maintain the equilibrium of the forklift when raising hefty products, the workers used their body weight as the counterweight, which practically caused casualties.
Case 3: The width of the forklift cargo goes beyond the allowed size of the path and hangs on the roadside shelf, which virtually creates an mishap.
Situation 4: Forklift is speeding and surrender throughout a turn.
Situation 5: The forklift chauffeur did not discover the pedestrian, and the pedestrian did not notice the forklift.
Instance 6: The forklift raises the workers illegally, the forklift vehicle driver does not put on the seat belt, the forklift lifter falls and the vehicle driver is squashed when the forklift rolls over.
Instance 7: The forklift motorist did not wear a safety belt and dropped from the car when it surrendered and was squashed.
Forklift operation need to take notice of these matters ：.

Start.
1. Prior to starting, observe the environments, and after verifying that there are no barriers that impede the safety of driving, beep the horn first and then begin.
2. For cars with hydraulic ( atmospheric pressure) brakes, the brake hydraulic pressure ( atmospheric pressure) gauge must be risk-free before beginning.
3. When the forklift starts with a tons, the driver must first verify that the load is steady and dependable.
4. The beginning should be slow-moving and stable.

Driving.
1. When driving, the elevation between the bottom end of the fork and the ground must be maintained 300mm-400mm, and the mast must be tilted backwards. .
2. Do not raise the fork too high when driving. When going into and leaving the work site or while driving, beware that there will certainly be no obstacles overhead. When the lots is traveling, the fork should not be elevated too high, which will impact the security of the forklift. .
3. After unloading, the fork must be decreased to the normal driving position before driving. .
4. When transforming, if there are pedestrians or vehicles nearby, the driving signal needs to be issued first. High-speed sharp turns are forbidden. High-speed doglegs will certainly cause the car to lose side security and topple. .
5. When the forklift is downhill, it is purely forbidden to turn off the flame and slide, and it is prohibited to brake unexpectedly while driving with lots unless there are unique circumstances.
6. When the forklift is running, it should follow the web traffic rules in the manufacturing facility and need to maintain a particular safety and security range from the vehicle ahead. .
7. When the forklift is running, the load must be in the lowest position that does not hinder the driving, and the gantry should be properly tilted back. The load will not be elevated other than when piling or filling. .
8. The elevation of the tons should not block the chauffeur's sight. In special circumstances, when the item affects the forward vision, drive at a low speed when reversing.
9. It is forbidden to turn on the ramp, neither to drive throughout the ramp. .
10. The risk-free driving speed of the forklift in the factory location is 5 km/h, and it has to drive securely at a low speed when getting in the manufacturing workshop area. .
11. When the forklift is lifted, raised or driven, it is restricted for workers to stand on the fork to hold items and play a stabilizing function. .
12. If problems are found, they will certainly be repaired and reported in a timely fashion, and they will never run with health problems or conceal them.

filling and dumping.
1. When Electric Forklift Truck for Warehouse fork-loading products, the range in between the two forks need to be changed as needed to make the lots of the two forks well balanced and not manipulated, and one side of the item need to be against the rack. .
2. It is prohibited to work with a solitary fork or utilize a fork top or draw. In special circumstances, safety and security warning signs have to be set up to advise surrounding pedestrians. .
3. In the process of packing and unloading products, the forklift must be stopped with the brake. .
4. The speed of the automobile should be slow-moving and stable. Take care not Stand-on Electric Pallet Stacker to roll the wheels on the dunnage, so as not to stretch the rolled items and hurt people. .
5. When making use of a fork to fork the goods, the fork ought to be as deep as feasible under the load, and it needs to be noted that the fork idea should not touch other items or objects. The tons needs to be stabilized with marginal back tilt of the gantry so that the tons does not glide backwards. The mast can be slanted onward slightly when the tons is decreased to allow for simple positioning of the lots and extraction of the forks. .
6. It is prohibited to fork items at broadband and collide with difficult items with the fork head. .
7. When the forklift is functioning, it is forbidden for people to stand around the fork, so regarding stay clear of the collapse of the goods and hurt people. .
8. Overwhelming is forbidden, and it is banned to use forks to lift workers to participate in high-altitude procedures to stay clear of high-altitude dropping accidents. .
9. It is not allowed to utilize the brake inertia to slide, place, round or roll things. .
10. It is not permitted to make use of forks to select, transform pallet unload.

Leaving .
1. It is forbidden to leave the forklift when the items on the fork are in the air. Before leaving the forklift, you should discharge the goods or lower the fork framework.
2. Pull the emergency brake manage to dead or dispirit the hand brake button.
3. The engine is shut off and the power is removed. (Except for unique scenarios, such as the motorist does not leave the automobile's view and does not go beyond 1 min).
4. Eliminate the secret. .

Forklift Operation Precautions.
1. Before and after the forklift operation, the appearance needs to be examined, and gas, lubing oil and cooling water ought to be added.
2. Examine the safety and security efficiency of starting, running and braking.
3. Check whether the lights and horn signals are full and reliable.
4. Throughout the operation of the forklift, check whether the stress and temperature level are typical.
5. After the forklift is running, the external leak needs to likewise be checked and the seals should be changed in time.

Forklift Safety Operation Specifications.
1. You need to inspect before leaving the car;.
2. When you run into somebody in front of you throughout driving, you must send a signal at a distance of 5 m;.
3. The driving rate in the manufacturing facility does not exceed 5 km/h;.
4. When driving, the low point of the freight must be 0.3 m ~ 0.4 m above the ground;.
5. The transforming must not be too sharp to stop the tendency of "free switching";.
6. Running up and down the incline ought to be slow and consistent, and no turning on the incline is allowed.
7. Do not drive throughout the gradient. When the slope is higher than 10%, the lorry must be driven backwards when declining;.
8. When the forklift personnel bring the goods and move forward, if they come across large or heavy items and go to the vehicle driver's line of vision, they need to take the reversing workout
.
The "Eight Prohibitions" should be complied with in the procedure.
1. Single fork procedure is not permitted.
2. It is not enabled to raise the goods for long distance driving.
3. It is not enabled to grab the goods by turning over the pallet with the fork.
4. It is not enabled to straight shovel chemicals, flammables and other dangerous chemicals with forks.
5. It is not permitted to use inertia force to grab the goods.
6. It is not permitted to use stopping pressure to expatriation round or easy-to-roll objects.
7. It is not enabled to bring individuals to work on the pallet or fork, and it is strictly prohibited to stand under the fork after the fork is elevated.
8. Do not drive side to side on slopes
.
Auto parking is not allowed under the following conditions.
1. Curves, slim roadways, train crossings;.
2. Areas with a longitudinal slope higher than 5%.
3. When there is an challenge on one side of the roadway, the contrary side of the area with the very same size as the barrier should be within 20 meters at each end.

Web：https://www.onenforklifts.com/
Email：[email protected]
Phone：+86 13827083844